Showing 60–70 of 14747 results

HPE ARUBA NETWORKING AP-500H-MNTD2 WLAN access point mount

The TL-SM5110-SR is designed to extend transfer distances based on 10Gbps Ethernet connectivity. It is a 10GBASE-SR high performance 850nm multi-mode SFP+ transceiver. It supports full duplex, 10G Ethernet connections up to 300m or 33m with 50/125µm or 62.5/125µm fiber cables respectively.

HPE R3J19A wireless access point accessory WLAN access point mount

Hewlett Packard Enterprise Q9G71A wireless access point accessory WLAN access point mount

Logitech PoE Injector with Plug Set Used for Cat5e Kit for Tap and Scribe

Axiom SFP1GSXA-AX network transceiver module Fiber optic 1000 Mbit/s SFP 850 nm

Universal Wall-Mount Bracket Secures and Organizes Your Wireless Access PointProtect your indoor Wi-Fi access point by mounting it high on a wall or ceiling, away from probing hands. This SmartRack® wall bracket is constructed from heavy-duty cold-rolled steel with a durable white powder-coated finish. It’s recommended for offices, dorms, hotels, classrooms, small businesses and other indoor areas where you need to keep your WAP secure, organized and out of the way, as well as strengthen a Wi-Fi signal in part of an office.Accommodates a Wide Range of WAPs, Including Cisco and ArubaThe ENBRKT fits most access-point bolt patterns and is compatible with Cisco low-profile and universal brackets. It also comes with a T-bar bracket for mounting Aruba and other WAP brands. Hardware is included for equipment installation. An open rear cutout allows easy cable routing and reduces cable clutter. The durable wall bracket comes ready for horizontal or vertical mounting on a wall or ceiling with user-provided hardware.

Adds PoE Devices to Your LAN Without a PoE SwitchNow you can add a surveillance camera, wireless access point, VoIP phone or other PoE (Power over Ethernet) device to your home or office network, even if your network switch doesn’t support PoE. Instead of making an expensive upgrade to a PoE switch, you can use this single-port PoE+ injector to send 30 watts of power, as well as Gigabit Ethernet data, through your existing Cat5e/6/6a cabling.Saves You Time and Money on Unnecessary Equipment UpdatesThis compact PoE plus injector delivers 10/100/1000 Mbps of data and up to 30 watts of power using existing Cat5e/6/6a cables. That means, in addition to not buying a new PoE network switch, you also don’t need to install new AC power lines and electrical outlets. This cost-effective midspan injector sends DC power and Ethernet data through your Ethernet cable, cutting down on cable clutter, equipment costs and installation time and labor.Expand Your Wireless Network Up to 328 ft.The NPOE-30W-1G delivers both power and data to any IEEE 802.3at (PoE+) or IEEE 802.3af (PoE) device up to 100 meters (328 feet) away. This allows you to install a device in a building lobby, on a ceiling, inside a warehouse or anywhere else an AC power outlet is unavailable. The PoE+ injector supports full-duplex 2 Gbps communication for sending and receiving data simultaneously. It also protects your device against short circuits, overloads and power surges.Simple Plug-and-Play Installation Has Your Device Connected in MinutesNo configuration or software is required to add the NPOE-30W-1G to your LAN. Just connect your switch or network jack to the shielded RJ45 Data port and your PoE device to the shielded RJ45 Power + Data port using existing Cat5e/6/6a cable. Connect the unit’s C14 inlet to a NEMA 5-15R outlet using the included power cord. LEDs indicate the unit is receiving power and is ready to transmit data.Designed for Installation Almost AnywhereMounting holes are featured for installing the midspan injector on a shelf, desktop, wall or any other smooth surface with user-supplied hardware. The black plastic housing fits in the palm of your hand, so it is small enough to hide away without interfering with your workflow or décor. The fanless design is ideal for silent operation.Typical Applications- Add a security camera to your network without upgrading to a new PoE switch- Install a touchscreen kiosk or VoIP phone in an area without a standard power connection- Fill in Wi-Fi dead spots in your office with a wireless access point connected to your LANPackage Includes- NPOE-30W-1G Gigabit PoE+ Midspan Active Injector - IEEE 802.3at, 30W, 1 Port- Detachable C13 to NEMA 5-15P power cord, 6 ft.- Owner’s manualSystem Requirements- Device that meets IEEE 802.3af or IEEE 802.3at standards

Omada 10GBASET RJ45 SFP+ ModuleSPEC: 10Gbps RJ45 Copper Transceiver, Plug and Play with SFP+ Slot, Support DDM Temperature and Voltage, Up to 30 m Distance Cat6a or above