Showing 230–240 of 653 results

The high-performance PCE-1G-01 1-Port Gigabit Ethernet PCI Express Card adds a 10/100/1000 Mbps network card and RJ45 Ethernet port to your computer or server. By adding the PCE-1G-01 to a computer with either no networking capabilities or 10/100 Ethernet, you can upgrade to Gigabit Ethernet capability without having to buy a new computer. It supports 10/100/1000 Mbps data rate auto-negotiation.Perfect for home or office, the PCE-1G-01 lets you connect to your high-speed LAN at Gigabit speeds up to 1000 Mbps. It easily installs inside your computer in just a few minutes. The standard bracket’s one-lane (x1) interface is compatible with x4, x8 and x16 PCIe slots. Allow the appropriate drivers to automatically install on your hard drive (a driver CD is included if they don’t), and connect a Cat5e/6 patch cable between the card’s RJ45 slot and your network. An LED indicates successful connection and network activity.The PCE-1G-01 is backward compatible with 10/100 Mbps networks and complies with PCI Express Revision 1.1. Fully compliant with IEEE 802.3, 802.3u and 802.3ab. Supports IEEE 802.3x full-duplex flow control, 802.1p Layer 2 priority encoding, 802.1a VLAN tagging, crossover detection and auto correction (auto MDI/MDI-X), Wake-on-LAN (WoL) and 9K Jumbo Frames.Adds 10/100/1000 Mbps Network Card and Ethernet Port to Your ComputerUpgrades your system to Gigabit Ethernet capability without buying a new computer or serverSupports 10/100/1000 Mbps data rate auto-negotiationPerfect for home or office useEasy to Install Inside Your Computer1-lane (x1) interface compatible with x4, x8 and x16 PCIe slotsAppropriate drivers install to your hard drive automaticallyLED indicates successful connection and network activityLoaded with the Latest FeaturesComplies with PCI Express Revision 1.1Fully compliant with IEEE 802.3, 802.3u and 802.3abSupports IEEE 802.3x full-duplex flow control, 802.1p Layer 2 priority encoding and 802.1a VLAN taggingSupports crossover detection and auto correction (auto MDI/MDI-X)Supports Wake-on-LAN (WoL) and 9K Jumbo FramesBackward compatible with 10/100 Mbps networks

Tripp Lite’s SUDC208V42P Power Distribution Cabinet supports 20-60kVA 3 phase UPS power distribution in critical datacenter equipment racks. Full size rack enclosure with pre-installed 42 pole circuit breaker panel supports 3 phase 208V and single phase 208V and 120V output via optional corded receptacle whips. Breaker panel includes 225A 3 pole main breaker, ground and neutral bars, plus 1/2 and 3/4 inch knockouts. Rack enclosure offers secure front and rear doors, removable side panels and shares common dimensions and overhead wiring tray accessories as Tripp Lite SR42UB rack enclosures. Compatible with Tripp Lite SUBB-series breakers, SUWL-series corded receptacle whips and a full line of compatible basic, metered, monitored and switched PDUs to support a variety of advanced network configurations.- SUDC208V42P Power Distribution Cabinet supports 20-60kVA 3 Phase UPS power distribution in critical datacenter equipment racks- Full size rack enclosure with pre-installed 42 pole circuit panel supports 3PH 208V and 1PH 208V and 120V via optional corded receptacle whips- Line up and match power distribution cabinet blends with existing standard datacenter racks for an aesthetically pleasing appearance while providing convenient connectivity between the centralized 3 phase UPS and protected electronic devices in equipment racks- Breaker panel includes 225A 3 pole main breaker, ground and neutral bars, 1/2 and 3/4 inch knockouts (see Help & Downloads for manual with detailed wiring information)- Rack enclosure offers secure front and rear doors, removable side panels and shares common dimensions and overhead wiring tray and ladder accessories as Tripp Lite SR42UB equipment racks- Requires appropriate SUBB-series output circuit breakers (see Related Items for list of compatible SUBB breakers)- Optional SUWL-series cable whips and SUWEL-series extensions support a variety of connector types, voltages and cable lengths (see Related Items for list of compatible SUWL-series and SUWEL-series cabling accessories)

The PCI-D9-02-LP 2-Port DB9 Serial PCI Card adds two DB9 serial ports to your computer or server. By adding the PCI-D9-02-LP to a computer with no DB9 ports or not enough of them, you can upgrade your DB9 capability without having to buy a new computer.Perfect for home or office, the PCI-D9-02-LP supports data transfer rates up to 115.2 Kbps on each port. It easily installs inside your computer in just a few minutes. The low-profile bracket’s interface is compatible with universal 3.3V and 5V 32-bit PCI/PCI-X slots. Allow the appropriate drivers to automatically install on your hard drive (a driver CD is included if they don’t), and connect DB9 serial extension cables (such as P520-006) to the card’s DB9 connectors.The PCI-D9-02-LP is fully compliant with PCI Local Bus Specification Revision 2.3 and compatible with industrial standard 16550 UART. On-chip 256-byte depth FIFO in transmit and receive paths of each port. Supports hardware and software flow control; PCI IRQ sharing and PCI power management; 5-, 6-, 7-, 8- and 9-bit serial formats; Even, Odd, None, Space and Mark parity; and 1- or 2-stop bit operation.Adds 2 DB9 (RS-232) Serial Ports to Your ComputerUpgrades your DB9 capability without buying a new computer or serverEach port supports data transfer rates up to 115.2 KbpsPerfect for home or office useLow-profile bracket to fit shorter casesEasy to Install Inside Your ComputerCompatible with universal 3.3V and 5V 32-bit PCI/PCI-X slotsAppropriate drivers install to your hard drive automaticallyLoaded with the Latest FeaturesComplies with PCI Local Bus Specification Revision 2.3Compatible with industrial standard 16550 UARTOn-chip 256-byte depth FIFO in transmit and receive paths of each portSupports hardware and software flow controlSupports PCI IRQ sharing and PCI power managementSupports 5-, 6-, 7-, 8- and 9-bit serial formatsSupports Even, Odd, None, Space and Mark paritySupports 1- or 2-stop bit operation

The PCE-D9-04-CBL 4-Port DB9 Serial PCI Express Card adds four DB9 serial ports to your computer or server. By adding the PCE-D9-04-CBL to a computer with no DB9 ports or not enough of them, you can upgrade your DB9 capability without having to buy a new computer. Its single-chip design provides optimum reliability and speed, reducing your CPU’s load from conventional bridge-chip cards and saving you money.Perfect for home or office, the PCE-D9-04-CBL supports data transfer rates up to 250 Kbps on each port with throughput up to 2.5 Gbps. It easily installs inside your computer in just a few minutes. The standard bracket’s one-lane (x1) interface is compatible with x4, x8 and x16 PCIe slots. Connect the included DB9 breakout cable to the card’s HD44 port, and allow the appropriate drivers to automatically install on your hard drive (a driver CD is included if they don’t). The PCE-D9-04-CBL is fully compliant with PCI Express Revision 1.1 and compatible with industrial standard 16450/16550 UART. On-chip 256-byte depth FIFO in transmit and receive paths of each port. Supports hardware and software flow control; 5-, 6-, 7- and 8-bit serial formats; Even, Odd, None, Space and Mark parity; 1- or 2-stop bit operation; and re-map function for legacy ports.Adds 4 DB9 (RS-232) Serial Ports to Your ComputerUpgrades your DB9 capability without buying a new computer or serverSingle-chip design reduces CPU load from conventional bridge-chip cardsEach port supports data transfer rates up to 250 KbpsPerfect for home or office useEasy to Install Inside Your Computer1-lane (x1) interface compatible with x4, x8 and x16 PCIe slotsAppropriate drivers install to your hard drive automaticallyIncluded breakout cable features 4 DB9 donglesLoaded with the Latest FeaturesComplies with PCI Express Revision 1.1Throughput up to 2.5 GbpsCompatible with industrial standard 16450/16550 UARTOn-chip 256-byte depth FIFO in transmit and receive paths of each portSupports hardware and software flow controlSupports 5-, 6-, 7- and 8-bit serial formatsSupports Even, Odd, None, Space and Mark paritySupports 1- or 2-stop bit operationSupports re-map function for legacy ports

The high-performance PCE-1G-01-LP 1-Port Gigabit Ethernet PCI Express Card adds a 10/100/1000 Mbps network card and RJ45 Ethernet port to your computer or server. By adding the PCE-1G-01-LP to a computer with either no networking capabilities or 10/100 Ethernet, you can upgrade to Gigabit Ethernet capability without having to buy a new computer. It supports 10/100/1000 Mbps data rate auto-negotiation.Perfect for home or office, the PCE-1G-01-LP lets you connect to your high-speed LAN at Gigabit speeds up to 1000 Mbps. It easily installs inside your computer in just a few minutes. The low-profile bracket’s one-lane (x1) interface is compatible with x4, x8 and x16 PCIe slots. Allow the appropriate drivers to automatically install on your hard drive (a driver CD is included if they don’t), and connect a Cat5e/6 patch cable between the card’s RJ45 slot and your network. An LED indicates successful connection and network activity.The PCE-1G-01-LP is backward compatible with 10/100 Mbps networks and complies with PCI Express Revision 1.1. Fully compliant with IEEE 802.3, 802.3u and 802.3ab. Supports IEEE 802.3x full-duplex flow control, 802.1p Layer 2 priority encoding, 802.1a VLAN tagging, crossover detection and auto correction (auto MDI/MDI-X), Wake-on-LAN (WoL) and 9K Jumbo Frames.Adds 10/100/1000 Mbps Network Card and Ethernet Port to Your ComputerUpgrades your system to Gigabit Ethernet capability without buying a new computer or serverSupports 10/100/1000 Mbps data rate auto-negotiationPerfect for home or office useLow-profile bracket to fit shorter casesEasy to Install Inside Your Computer1-lane (x1) interface compatible with x4, x8 and x16 PCIe slotsAppropriate drivers install to your hard drive automaticallyLED indicates successful connection and network activityLoaded with the Latest FeaturesComplies with PCI Express Revision 1.1Fully compliant with IEEE 802.3, 802.3u and 802.3abSupports IEEE 802.3x full-duplex flow control, 802.1p Layer 2 priority encoding and 802.1a VLAN taggingSupports crossover detection and auto correction (auto MDI/MDI-X)Supports Wake-on-LAN (WoL) and 9K Jumbo FramesBackward compatible with 10/100 Mbps networks

The P960-001-MSATA mSATA SSD to 2.5 in. SATA Enclosure Adapter Converter lets you use an mSATA SSD with a standard SATA-enabled computer, drive enclosure or docking station. To share data, just remove the adapter’s cover, connect the drive to the mSATA connector, secure it with the included screws, put the cover back, and connect the adapter to your computer’s SATA port. Or connect it to your computer’s USB port using a USB docking station, such as U339-000 (sold separately).The enclosed housing protects the drive when used in applications requiring more durability, such as hot-swap drive bays and external docking stations. The P960-001-MSATA supports SATA I, II and III drives and data transfer rates up to 6 Gbps. It’s plug-and-play, so no software, drivers or external power supply are required.

The P960-001-M2 M.2 NGFF SSD to 2.5 in. SATA Enclosure Adapter lets you use an M.2 NGFF SATA SSD (B-Key) drive with a standard SATA-enabled computer, drive enclosure or docking station. To share data, just remove the adapter’s cover, connect the drive to the M.2 NGFF connector, secure it with the included screws, put the cover back, and connect the adapter to your computer’s SATA port.The enclosed housing protects the drive when used in applications requiring more durability, such as hot-swap drive bays and external docking stations. The P960-001-M2 supports 2242, 2260 and 2280 M.2 SATA SSD drive types and data transfer rates up to 6 Gbps. It’s plug-and-play, so no software, drivers or external power supply are required.

The U438-06N-G1-W USB 3.1 Gen 1 to SATA III Adapter Cable connects a 2.5-inch SATA hard disk drive (HDD) or solid state drive (SSD) to an available USB-C or Thunderbolt™ 3 port on your laptop, tablet, Chromebook or computer. This lets you back up important data, retrieve data from an old hard drive, or store information on an external drive that you can take with you to another computer.This adapter cable supports USB 3.1 data transfer rates up to 5 Gbps. Its UASP (USB Attached SCSI Protocol) feature reduces latency and allows the cable to perform up to 70% faster when connected to a UASP-enabled host controller.Perfect for storing and sharing large files, such as music and video files, the U438-06N-G1-W is compatible with SATA drives up to 4 TB. Just insert the drive into the 22-pin SATA connector, and attach the built-in USB 3.1 cable to your computer.The U438-06N-G1-W accepts SATA III (6 Gbps), SATA II (3 Gbps) and SATA I (1.5 Gbps) drives, as well as USB 2.0 (480 Mbps) and USB 1.1 (12 Mbps) transfer speeds. It supports LBA-48 bit (Logical Block Addressing) and USB Mass Storage Class Bulk-Only Transport. No software, drivers or external power supply is required. Compatible with all USB-enabled operating systems.

Tripp Lite's U224-1R4-R is a kit that includes a 3-port USB 2.0 local transmitter unit, and a 1-Port USB 1.1 remote receiver unit. Connect up to 3 USB 2.0 devices to the local transmitter, while extending an additional USB 1.1 peripheral up to 45.72 m (150-ft.) from your computer. Simply plug the transmitter into the USB port on your computer, connect your USB peripherals, and run Cat5e/Cat6 cable up to 45.72 m (150-ft.) to the remote receiver unit and connected device. Plug-and-play; no software or drivers required.- Local transmitter unit features 3 USB 2.0 ports- Remote receiver unit features 1 USB 1.1 port- Locate a USB 1.1 peripheral up to 45.72 m (150-ft.) from your computer- Plug-and-play; no software or drivers required- Uses readily available Cat5e/Cat6 patch cable