Showing 10–20 of 46 results

Extend an HDMI and serial RS232 signal up to 300ft @1080p with no signal degradationThe HDMI+RS232 over Cat5 Transmitter, when paired with a receiver (not included- #29273) allows for the extension of an HDMI signal over solid conductor Cat5e/6 twisted pair cable* up to 300ft without signal degradation at a 1080p video resolution. This solution is compatible with any operating system and is truly plug and play with no drivers or software required. In addition, this solution utilizes TruChoice™ Power which provides the flexibility to power the system with a single power supply at either the transmitter or receiver end. HDBaseT technology allows the Extended Display Identification Data (EDID) signals, i.e. communication of the display’s capabilities, to pass through the extension solution ensuring that the content from the source is sent at the optimal resolution for the display. Built-in power surge protection and high ground loop immunity ensure high performance signal extension. The HDMI over Cat5 extenders support advanced HDMI features such as 3D, auto lip sync, deep color, Dolby & DTS 7.1 audio, CEC and a 10.2 Gbps data transfer rate. The serial RS232 port acts as a pass-through allowing remote control of the display.*Stranded Cat5e/6 cables may be used for HDMI extension applications up to 250ft. Shielded, solid conductor Cat5e/6 cabling is recommended for applications where the Cat5e/6 cable must be coiled, is run near other high-frequency signaling cables or in high EMI/RFI environments.- Single Cat5 cable required for HDMI extension- HDMI features supported- 3D- Auto lip sync- Deep color- Dolby & DTS 7.1 Audio- Consumer Electronics Control (CEC)- 10.2 Gbps- EDID pass through- FCC, CE, RoHS compliant- Requires a receiver to function - #29273

- Three methods for input switching: Auto, Manual, and Serial RS232- HDBaseT technology supports EDID pass through- Extend HDMI up to 115ft at 4k and up to 230ft at 1080p- Extend VGA up to 230ft at 1080p- Scales VGA video to a 1080p resolution- De-embeds audio from an HDMI A/V signalThe HDMI and VGA + Stereo Audio HDBaseT over Cat5 Extender Transmitter to Scaler / De-embedder kit is an ideal solution for extending audio/video signals from a Blu-ray player, laptop, Cable box, or other source device to a projector, HDTV, or Monitor. This kit extends HDMI, VGA and Stereo Audio signals over a single Cat5/Cat5e/Cat6 unshielded twisted pair network patch cable up to 230 feet at a 1080p resolution for HDMI and VGA, or 115 feet at 4k for HDMI. The local HDMI output allows an additional HDMI display to be supported via an HDMI cable. Switching between HDMI and VGA inputs is made easy with three options. The automatic switching option displays the last connected device. There are also two manual switching options. The first manual switching option is the buttons on the front of the transmitter. The second manual switching option is through Serial RS232 switching which accepts serial commands from a control device, like our TruLink A/V Controller. The built-in scaler up-scales VGA video to a 1080p resolution, ensuring that a high performance image is displayed . The de-embedder splits the audio from HDMI video and converts it to a Stereo Audio output to support an audio system that is separate from the display. This solution is compatible with any operating system and is truly plug and play with no drivers or software required. This solution utilizes TruChoice™ power, which allows power to be supplied over the Cat5 cable to both the transmitter and receiver from a single power adapter placed at either the transmitter or the receiver end of the solution. HDBaseT technology supports HDCP and allows the Extended Display Identification Data (EDID) signals, i.e. communication of the display’s capabilities, to pass through the extension solution ensuring that the content from the source is sent at the optimal resolution for the display. This transmitter is compatible with any of the HDMI HDBaseT receivers offered by C2G and works with our DB9 to RJ25 Serial RS232 cables.

This USB-A to USB-C Dongle Adapter Converter is an easy and convenient solution for connecting a USB-C cable, USB-C hub, or USB-C peripherals to a USB-A female port on a laptop or source device.Pair this adapter with a USB-A laptop and the Barco ClickShare to enjoy a hybrid meeting space with flexibility for virtual collaboration.Note: This USB-A to USB-C Adapter supports USB 2.0 (480 Mbps) and will not support video transmission.

The HDMI over Cat5 Receiver, when paired with a transmitter (not included- #29241) allows for the extension of an HDMI signal over solid conductor Cat5e/6 twisted pair cable* up to 300ft without signal degradation at a 1080p video resolution. This solution is compatible with any operating system and is truly plug and play with no drivers or software required. In addition, this solution utilizes TruChoice™ Power which provides the flexibility to power the system with a single power supply at either the transmitter or receiver end. HDBaseT technology allows the Extended Display Identification Data (EDID) signals, i.e. communication of the display’s capabilities, to pass through the extension solution ensuring that the content from the source is sent at the optimal resolution for the display. Built-in power surge protection and high ground loop immunity ensure high performance signal extension. The HDMI over Cat5 extenders support advanced HDMI features such as 3D, auto lip sync, deep color, Dolby & DTS 7.1 audio, CEC and a 10.2 Gbps data transfer rate.*Stranded Cat5e/6 cables may be used for HDMI extension applications up to 250ft. Shielded, solid conductor Cat5e/6 cabling is recommended for applications where the Cat5e/6 cable must be coiled, is run near other high-frequency signaling cables or in high EMI/RFI environments.- Single Cat5 cable required for HDMI extension- HDMI features supported- 3D- Auto lip sync- Deep color- Dolby & DTS 7.1 Audio- Consumer Electronics Control (CEC)- 10.2 Gbps- EDID pass through- FCC, CE, RoHS compliant- Requires a transmitter to function - #29241

The HDMI and VGA + Stereo Audio HDBaseT over Cat5 Extender Wall Plate Transmitter is an ideal solution for extending audio/video signals from a Blu-ray player and a laptop to a projector. This transmitter extends HDMI, VGA and Stereo Audio signals over a single Cat5/Cat5e/Cat6 unshielded twisted pair network patch cable up to 230 feet at a 1080p resolution. The rear cable connections for the Cat5 cable and the optional serial cable are set at 90°, making connections in a wall box easy. The local HDMI output of the front of the wall plate allows an additional HDMI display to be supported via an HDMI cable. Switching between HDMI and VGA inputs is made easy with three options available. Automatic switching displays the last connected device, manual switching via the button on the front of the wall plate, or Serial RS232 switching which accepts serial commands from a control device, like our TruLink A/V Controller This solution is compatible with any operating system and is truly plug and play with no drivers or software required. This solution utilizes TruChoice power, which allows power to be supplied over the Cat5 cable to both the transmitter and receiver from a single power adapter placed at either the transmitter or the receiver end of the solution. HDBaseT technology supports HDCP and allows the Extended Display Identification Data (EDID) signals, i.e. communication of the display’s capabilities, to pass through the extension solution ensuring that the content from the source is sent at the optimal resolution for the display. Built-in power surge protection and high ground loop immunity ensure high performance signal extension. This transmitter is compatible with any of the HDMI HDBaseT receivers offered by C2G and works with our DB9 to RJ25 Serial RS232 Cables.

The HDMI® HDBaseT + USB-B to A and RS232 over Cat Extender (18Gbps) allows for the extension of a 4K HDMI source up to 328ft to a 4K display without signal loss using a single Cat6a Ethernet cable. This is an ideal solution where USB must also be extended alongside HDMI video and audio to interactive whiteboards and displays or in any installation that goes far beyond the length limitations of standard HDMI and USB cabling.This HDMI HDBaseT 3.0 kit supports 5Play features, including the combined delivery of uncompressed ultra-high-definition digital video and audio, Ethernet, control signals, USB 2.0, and up to 100W of power through a single, 100m/328ft Cat6a LAN cable. The uncompressed digital video fully supports 4K 60Hz (4:4:4) HDMI signals and all audio formats in the HDMI 2.0 specification. The Ethernet pass-through transmits 1GB of data. The featured dip switch allows for RS232 pass-through and the added convenience of field firmware updating. USB 2.0 supports streaming cameras, connected peripherals, and storage devices. With one-way Power over HDBaseT (PoH) support, one power adapter connected to the receiver powers both the transmitter and receiver, so no additional power adapter required, allowing for greater flexibility in installations.Note: Ensure a solid reliable connection between the 4K HDMI HDBaseT Extender and critical equipment. We suggest using HDMI Cables with gripping connectors that provide greater port retention than standard HDMI connectors.Note: Shielded, solid conductor Cat6 or HDBaseT Certified Cat6a network cabling is recommended for applications where the category cable must be coiled, is run near other high-frequency signaling cables, or in high EMI/RFI environments.

This amplifier has been designed to mount under a desk, in a podium, or to nearly any flat surface with the ability to control the volume from a decorative style wall plate. This simple discreet solution provides sound reinforcement from a concealable amplifier capable of filling a class room, meeting room, huddle space, or work shop with rich sound while offering a convenient remote control that can be installed within reach.Send in the reinforcementIn a crowded room a speakers voice can quickly be lost to the noise. Ensure that every word can be heard with this simple audio reinforcement amplifier. Each word will be launched at the audience with 15 watts of power at 4Ω resistance providing distinct audio to all listeners.Command amplitudeThere is no need to search for controls or fiddle with settings when preparing to present. The remote control wall plate can be installed in the location that is most convenient to a presenter, ensuring a smooth start to any meeting.Need more inputDynamic presentations may require more than dazzling vocals to deliver the intended message. This amplifier incorporates a 3/4 inch microphone port and a 3.5mm stereo audio line level input, offering the ability to deliver reinforced content from an audio source such as a laptop or a triumphant oration leaving the audience astounded.Effortless deploymentThis amplifier simplifies audio reinforcement installation. No brackets or field terminations are required with this amplifier. Simply secure the amplifier with the built in mounting brackets to the desired location, attach speaker wires, and plug in a cat5e or cat6 cable to connect the remote control wall plate.

The C2G 2-Port VGA Auto Switch is perfect for switching between two source devices connected to a single display. For example, in a learning, sharing and collaborating environment, the VGA Auto Switch allows a document camera and a PC to be connected to a single VGA input on the display. The switch may be set so that the PC is displayed until the document camera is powered on causing an automatic switch that will allow the document camera to be displayed. When the document camera is powered off, the switch will then allow the PC to be displayed. The C2G 2-Port VGA Auto Switch has a small footprint allowing it to be placed in a convenient location for manual operation. No software is required for automatic or manual selection modes. The C2G 2-Port VGA Auto Switch features Extended Display Identification Data (EDID) copy, which ensures that the content from the source devices is sent to the display at the optimal resolution.

DisplayPort HDBaseT Extender over Cat Receiver (TAA Compliant)The DisplayPort HDBaseT over Cat Extender allows DisplayPort audio/video signals to be extended over a single Cat5e, Cat6, or Cat6a cable up to 300ft at a 1080p resolution. This receiver requires a DisplayPort or HDMI HDBaseT Transmitter for a complete solution. This solution is compatible with any operating system and is truly plug and play with no drivers or software required. This solution utilizes TruChoice power, which allows power to be supplied over the Cat cable to both the transmitter and receiver from a single power adapter placed at either the transmitter or the receiver end of the solution. HDBaseT technology supports HDCP and allows the Extended Display Identification Data (EDID) signals, i.e. communication of the display’s capabilities, to pass through the extension solution ensuring that the content from the source is sent at the optimal resolution for the display. Built-in power surge protection and high ground loop immunity ensure high performance signal extension.

The Cables To Go PC-TV adapter device allows you to convert your VGA signal from a computer to a composite out video so you can connect your PC, Mac or other VGA devices to your TV or projector. This is useful when connecting your computer to an older TV or projector, that doesn't support VGA, for large screen viewing. This device also comes with VGA and S-Video output ports to allow viewing on multiple displays which can support these signals. The converter kit comes with a USB power adapter so it can draw power from your computer instead of needing a dedicated outlet. This device's small footprint makes it easy for travel or to fit in tight spaces. The menu options allow for customization of display adjustment settings.