Showing 850–860 of 1150 results

SRT3000RMXLA-NCFeaturesAPC Smart-UPS SRT 3000VA RM 120V Network CardHigh density, double-conversion on-line power protection with scalable runtimeIncludes : CD with software , Documentation CD , Installation guide , Network Management Card , Rack Mounting brackets , Rack Mounting support rails , USB cable , Warranty card- 10/100 BaseT ConnectionConnect the device to a network using a 10 or 100 BaseT connection- Battery failure notificationProvides early-warning fault analysis on batteries enabling timely preventive maintenance- ECO ModeOperating mode that by-passes unused electrical components in good power conditions to achieve high operating efficiency without sacrificing protection- Green modePatent-pending operating mode that bypasses unused electrical components in good power conditions to achieve very high operating efficiency without sacrificing any protection.- LCD graphics displayText and mimic diagrams that display modes of operation, system parameters and alarms.- Rack/Tower convertibleProtects the initial investment in the UPS when migrating from tower to rack-mount environment.Serviceability- Audible alarmsProvides notification of changing utility power and UPS power conditions- Disconnected battery notificationWarns when a battery is not available to provide backup power.- Predicitive failure notificationProvides early-warning fault analysis ensuring proactive component replacement.- Automatic self-testPeriodic battery self-test ensures early detection of a battery that needs to be replaced.- User-replaceable batteriesIncreases availability by allowing a trained user to perform upgrades and replacements of the batteries reducing Mean Time to Repair (MTTR)Protection- Generator compatibleEnsures clean, uninterrupted power to protected equipment when generator power is used.- Cold-start capableProvides temporary battery power when the utility power is out.- Power conditioningProtects connected loads from surges, spikes, lightning, and other power disturbances.- Input power factor correctionMinimizes installation costs by enabling the use of smaller generators and cabling.- Frequency and voltage regulationGives higher application availability by correcting poor frequency and voltage conditions without using the battery.- Resettable circuit breakerEasy recovery from overloads; no need to replace a fuse.- Safety-agency approvedEnsures the product has been tested and approved to work safely with the connected service provider equipment and within the specified environment.Manageability- Network manageableProvides remote power management of the UPS over the network.- Serial connectivityProvides management of the UPS via a serial port.- SmartSlotCustomize UPS capabilities with management cards.- LED status indicatorsQuickly understand unit and power status with visual indicators.- InfraStruXure Manager CompatibleEnables centralized management via the APC InfraStruXure Manager.Adaptability- Plug-and-Play external batteriesEnsures clean, uninterrupted power to the loads when adding extra runtime to the UPS.- Flash upgradeable firmwareInstall maintenance releases of firmware remotely using FTP.- Rack/Tower convertibleProtects the initial investment in the UPS when migrating from tower to rack-mount environment.Availability- Temperature-compensated battery chargingProlongs battery life by regulating the charge voltage according to battery temperature.- Automatic internal bypassSupplies utility power to the connected loads in the event of a UPS power overload or fault.- Intelligent battery managementMaximizes battery performance, life, and reliability through intelligent, precision charging.- Scalable runtimeAllows additional run time to be quickly added as needed.- Automatic restart of loads after UPS shutdownAutomatically starts up the connected equipment upon the return of utility power.- Hot-swappable batteriesEnsures clean, uninterrupted power to protected equipment while batteries are being replacedMarketing Features- Avoids costly power problems by keeping your IT equipment and data protected and available.Network grade power conditioning protects from damaging surges and disruptive noise. The double conversion architecture provides tight voltage regulation, frequency regulation ,and zero transfer time to battery during power events.- Low operating and maintenance costs with proven reliability and intelligent battery management.Intelligent battery management, pioneered by APC, maximizes battery performance and life through intelligent, precision temperature compensated charging. Automatic self tests insure battery reliability and warn customers in advance of battery replacement. Convenient, easy to connect, hot-swappable battery modules provide battery replacement without powering down.- Save time with easy and convenient remote accessibility.Network manageable via serial, USB or optional Ethernet. Includes Powerchute® Network Shutdown Software for convenient monitoring and control, safe operating system shutdown, and innovative energy management capabilities.- Peace of mind that comes with full equipment compatibility and reliability of a leaderProvides pure sine wave output which is recommended by server manufacturers using active power factor corrected (PFC) power supplies. Safety agency tested and approved means that you can deploy Smart-UPS with confidence that they meet or exceed the industry’s most rigorous standards.

Liebert GXT3-MT on-line uninterruptible power supply (UPS) is a compact mini-tower model ideal for protecting sensitive electronics in a non-rack environment. The UPS offers intelligent monitoring and network management functions.Flexibility- Compatible with backup generator — handles frequency variations and other power fluctuations that occur during generator operation.- Offers a variety of monitoring options via Liebert IntelliSlot interface.- Provides six battery backed outlets to accommodate protection for more equipment.Higher Availability- Protects against and conditions all forms of power anomalies.- Assures continuity of power to critical loads during system maintenance or in case of internal fault with internal automatic and manual bypass.- Operates with a wider input voltage window for fewer transfers to battery, saving battery wear and tear.- Allows fast and easy maintenance with user-replaceable hot-swappable batteries.- Notifies users with advance early warning of UPS status via automatic and manual battery test feature.- Operates compatibly with Liebert MicroPOD maintenance bypass and power output distribution module.Lowest Total Cost Of Ownership- Corrects for frequency variations without switching to battery, resulting in longer battery life.- Protects your investment with a standard two-year warranty with paid shipping both ways. Also available with optional extensions of one year or three years.Ideally Suited For- PCs- Network workstations- Test and diagnostic equipment

Battery-protected and surge-only outlets Reserves power capacity and run time for connected equipment that require UPS battery back-up while providing surge only protection for less critical equipmentSafety-agency approvedEnsures the product has been tested and approved to work safely with the connected service provider equipment and within the specified environment.Battery and surge protected outletsBack up and protect your hardware and data during power outages, surges and spikes.Surge only outletsProtect secondary electronics from surges and spikes without reducing battery power used to run primary electronics during an outage.Audible alarmsProvides notification of changing utility power and UPS power conditionsLED status displayQuickly understand unit and power status with visual indicators.

Tripp Lite SmartPro Line Interactive UPS with enhanced LCD interface offers network-grade power protection for critical server, network and telecommunications equipment. Line Interactive Uninterruptible Power Supply (UPS) with built-in Auto-Voltage Regulation (AVR) actively corrects brownouts and overvoltages back to usable levels while maintaining a full battery charge in case of power failure. Tripp Lite's unique configuration excels in exceptionally poor-power environments with two separate levels of voltage boost to correct both slight undervoltages and severe brownout conditions. Interactive LCD interface reports UPS operating mode, detailed UPS and site-power data, plus enables a variety of UPS setup and configuration options. Super-fast switchover from line to battery power occurs within milliseconds to maintain operation of connected equipment without interruption or reboot. 98% line-mode efficiency offers reduced heat emissions and operating costs. Network management interfaces support communications via USB, RS-232 and optional SNMPWEBCARD network interface. HID-compliant USB port enables integration with built-in power management and auto shutdown features of Windows and Mac OS X. Network communications ports enable detailed monitoring of equipment load levels, self-test data and utility power conditions. Includes PowerAlert monitoring software and complete cabling. Switched output load banks enable scheduled and real-time remote reboot and load shedding of select outlets. Emergency Power Off (EPO) interface. LCD display panel easily rotates for viewing in rackmount or tower configurations. Audible alarm with push-button momentary alarm-cancel and silent-mode configuration options. Programmable self-test. Field-replaceable, hot-swappable battery modules.- Tripp Lite SMART3000RM2U line interactive 2U rack/tower UPS with 3000VA / 3kVA capacity (1600W maximum load with external battery packs)- Line interactive UPS with Automatic Voltage Regulation (AVR) corrects brownouts and overvoltages from 83 to 145V- NEMA L5-30P input plug; 8 NEMA 5-15/20R and 1 L5-30R output receptacles, Two independently switchable output load banks- Maintains uninterrupted operation of connected networking equipment during blackouts, surges, brownouts and overvoltages- High 98% efficiency rating in line-power mode offers reduced power consumption and BTU emisssions- Internal batteries offer 10 minutes at 50% load (1125W) and 3.5 minutes at 100% load (2250W)- Extended runtime is available with optional BP48V24-2U (limit 1), BP48V60RT-3U (multi-pack compatible) and BP48V27-2US (multi-pack compatible) external battery packs (max output de-rates to 1600 watts with external batteries)- External battery configurations require the use of Tripp Lite's External Battery Configuration Software (see manual)- Hot-swappable, user-replaceable internal batteries and external battery packs can be replaced with no disruption to connected equipment- Front panel LCD monitoring screen with MODE and ENTER buttons reports operating mode with 5-bar battery charge graphic, plus 7 selectable screens of detailed UPS and site power information- LCD interface also supports a number of advanced user setup and operating preferences- Ships with 4 post rackmount installation hardware; Optional 2POSTRMKITWM enables 2 post rackmount/wallmount installation; Optional 2-9USTAND enables tower placement- Built-in USB, RS-232 and optional SNMPWEBCARD accessory monitoring options- HID-compliant USB port enables integration with built-in power management and auto shutdown features of Windows and Mac OS X- Included PowerAlert UPS monitoring software; Built-in Emergency Power Off (EPO) interface with cable

Tripp Lite's SmartOnline SU1500XL on-line, double conversion UPS protects critical server, networking or telecommunications equipment from blackouts, brownouts, voltage fluctuations and surges. Large-capacity 1.5kVA/1200W UPS continuously converts incoming AC to DC, then back to perfect sine wave AC output at 120V AC (+/-2%). Removes harmonic distortion, fast electrical impulses, frequency fluctuations and other hard-to-solve power problems not addressed by other UPS systems. True sine wave output and zero transfer time provides guaranteed compatibility with all equipment types. Highly efficient operation in optional economy mode setting, saving BTU heat output and energy costs. Includes 6 UPS-supported outlets. 2 load banks, each with 3 outlets, can be independently controlled via a software interface to selectively reboot remote equipment or automatically shed less critical loads to extend battery runtime for the most critical equipment. Battery backup time can be extended with the addition of multiple external battery packs. Includes slot for internal SNMP/web card, plus DB9 enhanced serial monitoring port for unattended shutdown, remote control and monitoring of UPS system and power data. HID-compliant USB interface enables integration with built-in power management and auto shutdown features of Windows and Mac OS X. Includes Tripp Lite's PowerAlert UPS Power Management Software. Compatible with Tripp Lite's Watchdog Service Monitoring/Rebooting Software. Attractive all-black upright tower format. $250,000 Ultimate Lifetime Insurance (U.S., Canada, and Puerto Rico only)- True on-line, double conversion UPS provides constant, pure sine wave AC output- Zero transfer time, on-line, double-conversion and economy-mode operation supported- Maintains continuous operation through blackouts, brownouts, voltage fluctuations and surges with zero transfer time- Removes harmonic distortion, electrical impulses, frequency variations and other hard-to-solve power problems- Accepts input voltages between 80V and 150V (65V to 150V at loads under 70%), regulating output to 120V AC +/-2%- 1500VA/1200W output capacity with 6 NEMA 5-15R outlets- Two built-in, individually switchable load banks, each with 3 outlets, can be controlled via software interface to selectively reboot remote equipment or automatically shed less critical loads to extend battery runtime for the most critical equipment- Standard internal battery set provides 14 min. runtime at half load and 4.5 min. at full load- Runtime is expandable with BP48V24-2U (limit 1), BP48V60RT-3U (multi-pack compatible) and BP48V27-2US (multi-pack compatible) external battery packs- Some external battery configurations require the use of Tripp Lite's External Battery Configuration Software (see manual)- Attractive all-black upright tower format- Simultaneous communications via HID-compliant USB port, DB9 serial port, and SNMP/web card slot- HID-compliant USB interface enables integration with built-in power management and auto shutdown features of Windows and Mac OS X- DB9 serial network interface supports RS-232 and contact closure messaging- Slot for optional SNMP/web card (part# SNMPWEBCARD)- Included PowerAlert UPS Power Management Software and cabling provides monitoring of in-depth site power conditions, full UPS status and fault warnings, output load level and load bank power control- Compatible with Tripp Lite's WatchDog Service Monitoring/Rebooting Software (part # WATCHDOGSW)- Fault tolerant electronic bypass maintains utility output during a variety of UPS fault conditions- Diagnostic LEDs- Built-in RJ-11 EPO (Emergency Power Off) jack allows connection to site emergency power off systems- $250,000 Ultimate Lifetime Insurance (U.S., Canada, and Puerto Rico only) for connected equipment (USA and Canada Only)

The SMX1050SLT SmartPro® 230V 1.05kVA 650W Line-Interactive Sine Wave UPS provides battery backup and AC power protection against blackouts, brownouts, power surges and line noise that can damage electronics or destroy data. Ideal for backing up point-of-sale applications, VoIP systems and small business networks, the SMX1050SLT switches to battery mode in milliseconds to keep your connected equipment running long enough to save files and shut down safely with no data loss.Featuring eight C13 outlets and a C14 inlet that accepts a user-supplied AC power cord, the SMX1050SLT has an internal battery that provides 20 minutes of support at half load and seven minutes at full load. Front-panel LEDs indicate line power, voltage regulation, load level and battery status. An alarm sounds to indicate power failure or overload.Automatic voltage regulation (AVR) maintains selectable 220V, 230V or 240V nominal output over an input range of 174V–266V (220V), 182V–278V (230V) or 190V–290V (240V) without using battery power. EMI/RFI noise filtering improves your equipment’s performance and prevents damage. A 350-joule surge suppression rating protects your equipment from harmful power surges. With downloadable PowerAlert® software, the SMX1050SLT enables safe unattended system shutdown and file saves in case of a prolonged power failure. Adding an optional network management card permits remote management of the UPS, including reboots and activity logs.Protects Mission-Critical EquipmentProvides fully regulated sine wave AC output for point-of-sale applications, VoIP systems and small business networksAudible alarm signals loss of utility power or overload8 C13 outletsC14 inlet accepts user-supplied AC power cord with country-specific plug350-joule surge suppression ratingReliable Battery BackupSupports half load up to 20 min. and full load up to 7 min.Internal batteries designed for hot-swap field replacementCold-start capability enables turn-on in battery mode during blackoutsAutomatic Voltage Regulation (AVR)Maintains selectable nominal output without using battery powerCorrects brownouts and overvoltages from 174V–266V (220V), 182V–278V (230V) or 190V–290V (240V)EMI/RFI Line Noise FilteringRemoves electromagnetic and radio frequency interference that can disrupt or damage equipment’s performanceLED IndicatorsFront-panel LEDs indicate line power, voltage regulation, load level and battery statusOptional Network Management CardsCompatible with UPS management card options WEBCARDLX, SNMPWEBCARD and RELAYIOCARDOptional WEBCARDLX (sold separately) with the latest version of PowerAlert Device Manager firmware (PADM20) provides enhanced remote management capabilitiesPADM20 and PowerAlert Element Manager (PAEM) form a powerful tool for expanding maintenance functions in large installations, including firmware update checks and backup and restoration of device configurationsCommunication PortsUSB & Serial ports enable data-saving unattended shutdown when used with PowerAlert software, available via FREE download from tripplite.eaton.com/products/power-alert Telephone/Network JacksProtect against power surges over telephone/DSL or network Ethernet lines

This parts kit contains spare parts for the APC product model shown.